✔ Competitive Pricing                              ✔ Quality Service                           ✔ Extensive Stock                          ✔ Experienced Staff

Facebook Instagram Twitter Email
Pricing  
Westcountry Machinery 4 Wood
Menu
Search

Pen Turning - A Beginners Guide

zz Knowledge Centre > Pen Turning - A Beginners Guide

A Beginners Guide to Pen Turning

Starting Out Pen Turning

Turning pens is a very rewarding and enjoyable pastime. Whether you are a seasoned woodturner or a newbie, pen turning is a quick and easy skill that requires a minimum of turning equipment. There are many different styles available, from the standard ballpoints, rollerballs and fountain pens as well as propelling and click pencils.You will also discover a wide variety of plating finishes, from 24k gold plating right through to Rhodium plating that will last a lifetime. There is also an almost endless choice of man made acrylics and resin blanks.

Pen Blank Selection

The choice of pen blanks is almost endless and covers the full spectrum of wood available for turning, as well as man made materials such as acrylic, and natural material such as animal horn.
When choosing your pen blank, remember that a turned pen has very little surface area and can look plain if the material used is too bland. When choosing a wooden blank ensure it has an interesting figuring or, in the case of man made materials, it has colour contrasting ripples. Also keep in mind that some wood, such as Paduak and Purpleheart, have vibrant colour when first turned, but fade after time to become very uninteresting.
Pen blanks can vary in size from approximately 1/2 Inch to 1 Inch square, and 4.1/2 Inch to 6 Inch long. Ensure that you select the correct size blank for the specific pen you are going to turn. We recommend beginners use a bigger blank and turn it down.
If you have chosen exotic woods such as Snakewood, Cocobolo and Kingwood, ensure the blank is dry and free from any cracks or faults, as these will cause problems down the line.
Find wooden pen blanks here
Find acrylic pen blanks here

Tools and Equipment

Lathes

It is recommended that you turn using a lathe speed of 2500rpm or faster to ensure a clean cut on such a small surface area. Most wood turning lathes have this capability. Small, more compact lathes are more suitable for pen turning, however pens can be turned on any size of lathe.

Drills

When drilling, remember to keep the drill moving and clear any shavings away to reduce heat build up, as this will damage the wood and cause splitting. Pen blanks can be drilled either in the lathe using a chuck in the headstock and a standard drill chuck in the tailstock, or held vertically in a vice/clamp and drilled using a pillar/banch drill.

Pen Mandrels

Pen mandrels are a very helpful piece of equipment when turning pens as they ensure the pen runs accurately in the lathe. A pen mandrel is a steel bar machined accurately and is held in the lathe using a chuck, or more commonly using a drill driver, although many mandrels already have a drill driver as an integral part. We recommend you purchase a double pen mandrel, which is long enough to accomodate both parts of the pen. This allows for more accurate turning and consistancy in wall thickness, eliminating any problems that may occur when building the pen. Due to the different tube sizes of the many various pens available, there are matching bushing sets to slide over the mandrel and fit accurately into the ends of both tubes to ensure they turn concentrically. When the tubes and bushes are in place the tailstock is bought up into place and holds everything securely, ready to be turned.

Drill Drivers

A drill driver is used to securely hold the mandrel in place and to drive the mandrel via the lathe spindle. They are available in 1 or 2MT depending on the bore of the headstock spindle in your lathe. One end of the pen mandrel fits tightly into the drill driver and the other normally has a small cup end into which a standard revolving centre fits.

Glues and Adhesives

It is important to select the correct glue when making pens. Cyanoacylate or super glue ensures a strong bond, but is expensive and inflexible, with a quick setting time and little time for adjustment. Polyurethane adhesive is more cost effective, very flexible with a longer setting time, and can also be used as a gap filler if required.

Abrasives

When using abrasives on turned pens, keep the abrasive moving at all times and ensure the wood does not get hot. If the wood becomes hot damage will occur such as splitting and cracking.

Finishes

Waxes can be used to give a high shine but due to a pen being handled so much, a wax finish will not last very long, and also collects dust and dirt over time. Friction polish is more durable and gives a high gloss finish, and is easy to apply while the pen is still on the lathe.

Health and Safety

As with all woodworking it is essential that a dust mask and safety goggles be worn due to the hazards of wood dust and shavings. Also ensure that glue is used in a well-ventilated area and has set prior to switching the lathe back on, so as not to flick glue into your face.

Take a look here for everything you need to start turning pens.

Have fun creating beautiful pens!




 

Join our mailing list to receive
exclusive offers and discounts